Section PEF_Conf
	## Possible values: Yes/No
	Enable_PEF                                    No
	## Possible values: Yes/No
	Enable_PEF_Event_Messages                     No
	## Possible values: Yes/No
	Enable_PEF_Startup_Delay                      No
	## Possible values: Yes/No
	Enable_PEF_Alert_Startup_Delay                No
	## Possible values: Yes/No
	Enable_Alert_Action                           No
	## Possible values: Yes/No
	Enable_Power_Down_Action                      No
	## Possible values: Yes/No
	Enable_Reset_Action                           No
	## Possible values: Yes/No
	Enable_Power_Cycle_Action                     No
	## Possible values: Yes/No
	Enable_OEM_Action                             No
	## Possible values: Yes/No
	Enable_Diagnostic_Interrupt                   No
	## Give value in seconds
	Startup_Delay                                 75
	## Give value in seconds
	Alert_Startup_Delay                           75
EndSection
Section Community_String
	## Give valid string
	Community_String                              
EndSection
Section Lan_Alert_Destination_1
	## Possible values: PET_Trap/OEM1/OEM2
	Alert_Destination_Type                        OEM1
	## Possible values: Yes/No
	Alert_Acknowledge                             No
	## Give valid unsigned number in seconds
	Alert_Acknowledge_Timeout                     2
	## Give valid unsigned number
	Alert_Retries                                 3
	## Possible values: Default/Backup
	Alert_Gateway                                 Default
	## Give valid IP address
	Alert_IP_Address                              0.0.0.2
	## Give valid MAC address
	Alert_MAC_Address                             00:00:00:00:00:00
EndSection
Section Alert_String_1
	## Give valid number
	Event_Filter_Number                           0
	## Give valid number
	Alert_String_Set                              0
	## Give string. Max 64 chars.
	Alert_String                                  
EndSection
Section Alert_Policy_1
	## Possible values: Always_Send_To_This_Destination/Proceed_To_Next_Entry/Do_Not_Proceed_Any_More_Entries/Proceed_To_Next_Entry_Different_Channel/Proceed_To_Next_Entry_Different_Destination_Type
	Policy_Type                                   Always_Send_To_This_Destination
	## Possible values: Yes/No
	Policy_Enabled                                No
	## Give a valid number
	Policy_Number                                 0
	## Give a valid number
	Destination_Selector                          0
	## Give a valid number (LAN = 1)
	Channel_Number                                0
	## Give a valid number
	Alert_String_Set_Selector                     0
	## Possible values: Yes/No
	Event_Specific_Alert_String                   Yes
EndSection
Section Event_Filter_1
	## Possible values: Manufacturer_Pre_Configured/Software_Configurable/Reserved1/Reserved3
	Filter_Type                                   Software_Configurable
	## Possible values: Yes/No
	Enable_Filter                                 Yes
	## Possible values: Yes/No
	Event_Filter_Action_Alert                     Yes
	## Possible values: Yes/No
	Event_Filter_Action_Power_Off                 Yes
	## Possible values: Yes/No
	Event_Filter_Action_Reset                     Yes
	## Possible values: Yes/No
	Event_Filter_Action_Power_Cycle               Yes
	## Possible values: Yes/No
	Event_Filter_Action_Oem                       Yes
	## Possible values: Yes/No
	Event_Filter_Action_Diagnostic_Interrupt      Yes
	## Possible values: Yes/No
	Event_Filter_Action_Group_Control_Operation   Yes
	## Give a valid number
	Alert_Policy_Number                           2
	## Give a valid number
	Group_Control_Selector                        2
	## Possible values: Unspecified/Monitor/Information/OK/Non_Critical/Critical/Non_Recoverable
	Event_Severity                                Information
	## Specify a hex Slave Address or Software ID from Event Message or 0xFF to Match Any
	Generator_Id_Byte_1                           0x03
	## Specify a hex Channel Number or LUN to match or 0xFF to Match Any
	Generator_Id_Byte_2                           0x00
	## Specify a Sensor Type, For options see the MAN page
	Sensor_Type                                   Current
	## Specify a Sensor Number or 0xFF to Match Any
	Sensor_Number                                 0x03
	## Specify a Event/Reading Type Number or 0xFF to Match Any
	Event_Trigger                                 0x04
	## Give a valid number
	Event_Data1_Offset_Mask                       0x05
	## Give a valid number
	Event_Data1_AND_Mask                          0x06
	## Give a valid number
	Event_Data1_Compare1                          0x07
	## Give a valid number
	Event_Data1_Compare2                          0x08
	## Give a valid number
	Event_Data2_AND_Mask                          0x09
	## Give a valid number
	Event_Data2_Compare1                          0x11
	## Give a valid number
	Event_Data2_Compare2                          0x12
	## Give a valid number
	Event_Data3_AND_Mask                          0x13
	## Give a valid number
	Event_Data3_Compare1                          0x14
	## Give a valid number
	Event_Data3_Compare2                          0x15
EndSection